Teach Your Kid Electronics

Advanced · Project 13

AM Radio

Build a real radio that picks real stations out of the air. A coil antenna and a tuning knob choose the station, a tiny radio chip turns it into sound, and the LM386 makes it loud.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Advanced⏱ About 50 min

🧰 What you need

  • 1×Full-size breadboardThe big brother of the half-size board: twice as long, with room for several chips.
  • 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 3×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 1×MK484 AM radio chipA whole AM radio receiver in a 3-legged package that looks like a transistor. TA7642 is the same chip.
  • 1×AM ferrite rod antenna coilA coil of copper wire on a dark magnetic rod. It picks up AM radio waves.
  • 1×AM tuning capacitorA capacitor with a knob: turning it picks the radio station. Often sold together with the antenna coil.
  • 1×LM386 audio amplifierMakes a weak sound signal strong enough to drive a speaker.
  • 2×1N4148 diodeA small, fast one-way valve for signals. The end with the black band is the cathode (−).
  • 1×10 kΩ potentiometer (knob)A resistor you can change by turning a knob. Three legs: two ends and a middle "wiper".
  • 2×1 kΩ resistor — brown, black, red, goldColors: brown, black, red, gold.
  • 1×100 kΩ resistor — brown, black, yellow, goldColors: brown, black, yellow, gold.
  • 1×0.01 µF capacitorA tiny disc capacitor, often printed "103". It has no + or −.
  • 1×1 µF capacitorA small can-shaped capacitor. The striped leg is −.
  • 1×220 µF capacitor (can-shaped)A medium can that passes sound on to a speaker while blocking the steady voltage. The striped leg is −.
  • 1×Small speaker, 8 Ω — a passive buzzer works too, but a speaker sounds much betterLouder and better-sounding than a passive buzzer for music and radio.
  • 14×Jumper wireA short wire with stiff ends that push into the breadboard.

✨ The finished project

↔ Big board! Scroll sideways to see all of it.

An AM radio: a ferrite-rod antenna and tuning knob feed an MK484 radio chip, and an LM386 amplifier drives the speaker ++−−++−−aabbccddeeffgghhiijj115510101515202025253030353540404545505055556060 10kΩ 0.01µF 1µF 220µF LM386 +passive antenna coil tuning MK484OIG 1 kΩ 1 kΩ 100 kΩ 1N4148 AAAAAA3 × AA = 4.5 V+−
An AM radio: a ferrite-rod antenna and tuning knob feed an MK484 radio chip, and an LM386 amplifier drives the speaker ++−−++−−aabbccddeeffgghhiijj115510101515202025253030353540404545505055556060 10kΩ 0.01µF 1µF 220µF LM386 +passive antenna coil tuning MK484OIG 1 kΩ 1 kΩ 100 kΩ 1N4148 AAAAAA3 × AA = 4.5 V+−
Schematic: An AM radio: a ferrite-rod antenna and tuning knob feed an MK484 radio chip, and an LM386 amplifier drives the speaker INOUTGNDMK484 + + IN+3IN-2OUT5GAIN11VS6GAIN88GND4BYPASS7LM386U2 + + +4.5V 4.5 V 1 kΩ 1N4148 1 kΩ 100 kΩ 0.01 µF antenna coil tuning knob 1 µF volume 220 µF passive buzzer
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

🔣 New schematic symbols

This project’s schematic has some symbols you haven’t seen before. Here’s what they mean.

  • Coil (antenna)

    Bumps in a line are a coil: wire wound round and round. The two lines above it mean it’s wound on a magnetic (ferrite) rod. Radio waves passing by make tiny currents in it.

  • Tuning capacitor

    A capacitor with an arrow through it: a capacitor you can change by turning a knob. In a radio it picks which station you hear.

Right now, the air around you is full of invisible radio waves, carrying music, news and talk from radio stations miles away. They’re a kind of light our eyes can’t see. In this project you’ll build a radio that catches them, picks out one station and plays it.

How radio works

A radio station sends out a wave that wiggles about a million times a second. That speed is its frequency: every station has its own, and it’s the number on the radio dial (like 880 kHz, which means 880,000 wiggles a second). The sound rides on top by making the wave stronger and weaker. That’s what AM means: amplitude modulation, “changing the strength”.

Our radio does four jobs:

  1. Catch: the antenna coil is wire wound round a ferrite rod. Ferrite is a dark, magnetic material that gathers in radio waves, and they make tiny currents in the coil.
  2. Choose: the coil and the tuning capacitor together “ring” at one frequency, like a swing that goes highest when you push it at just the right moments. Turning the tuning knob changes which station rings loudest; the others fade away.
  3. Listen: the MK484 radio chip amplifies the chosen station and pulls the sound out of it.
  4. Make it loud: the LM386 amplifier from the Loudspeaker Amplifier drives the speaker, with a volume knob.

Power for the radio chip

The MK484 looks like a transistor, but it’s a whole radio inside. It runs on only 1.1–1.6 V: more than that, and it squeals. Here’s a neat trick to get that from our 4.5 V batteries: a diode always “uses up” about 0.7 V when current flows through it. So two diodes in a row, fed through a 1 kΩ resistor, hold a point at about 1.4 V. The chip gets its power from there through another 1 kΩ resistor, into its OUT leg (yes, really: it shares one leg for power and sound).

Its legs, flat side facing you: OUT, IN, GND.

Build it

  1. Bottom − rail: black T-1 → B-1 (bottom blue − rail, column 1).

  2. 1.4 V supply: 1 kΩ a5 → T+5 (top red + rail, column 5). Diodes (bands to the right): b5 → b8, then c8 → c11. Black a11 → T-11 (top blue − rail, column 11).

  3. Radio chip: flat side facing you, O b13, I b14, G b15. 1 kΩ e5 → e13. GND: black e15 → f15, j15 → B-15 (bottom blue − rail, column 15).

  4. Bias: 100 kΩ c13 → c19. Green e19 → f19. 0.01 µF capacitor j19 → B-20 (bottom blue − rail, column 20) (it has no + or −).

  5. Antenna and tuning: green e14 → f14. Coil leads in h14 and h19. Tuning capacitor legs in j14 and j17; green i17 → i19.

  6. Sound out: 1 µF capacitor + d13, − d18. Orange b18 → b22. Volume knob in d22, d23, d24; black a24 → T-25 (top blue − rail, column 25). Orange e23 → f23, then h23 → h32 (LM386 IN+).

  7. LM386: notch on the left, pin 1 in f30. Red a32 → T+32 (top red + rail, column 32); black j33 → B-33 (bottom blue − rail, column 33); black j31 → B-31 (bottom blue − rail, column 31).

  8. Speaker: 220 µF capacitor + c33, − c37. Speaker + b37, − b40. Black a40 → T-41 (top blue − rail, column 41).

  9. Power: 3×AA red into T+1, black into T-3. Turn the volume up and slowly turn the tuning knob. 📻

The build check can’t simulate radio waves, but it checked every connection, and that the radio chip gets the right voltage (1.1–1.6 V) with both normal and fresh batteries.

Finding stations

  • Turn the tuning knob slowly. Stations come and go over a tiny turn.
  • Rotate the whole board. A ferrite antenna hears best side-on to the station, so turning the radio can make a weak station loud.
  • Go near a window, and away from computers, TVs and phone chargers: they make radio “noise”.
  • Try at night. AM waves travel much further after dark, bouncing off the sky. You might hear stations hundreds of miles away!

Not working?

  • Silence, not even a hiss? Check the LM386 first: touch a finger to its IN+ column and you should hear a buzz.
  • Hiss, but no stations? Turn the tuning knob slowly through its whole range, and rotate the board. Check the coil’s leads are scraped clean of their coating where they go into the board.
  • A loud squeal? The radio chip is getting too much voltage: check both diodes are there, bands to the right.

Try it!