Teach Your Kid Electronics

Advanced · Project 9

Quiz Buzzer

A two-player game-show buzzer. Whoever presses first lights up, and the other player is locked out until the quizmaster presses RESET.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Advanced⏱ About 40 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 3×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 1×74HC74 flip-flop chipTwo D flip-flops: tiny memories that each store one bit (on or off).
  • 3×Push button (tactile switch)A little button with 4 legs. It connects its two sides only while you press it.
  • 3×10 kΩ resistor — brown, black, orange, goldColors: brown, black, orange, gold.
  • 2×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
  • 2×5 mm LED (any color) — two different colors, one per playerA tiny light that only lets current flow one way. The long leg is +.
  • 17×Jumper wireA short wire with stiff ends that push into the breadboard.

✨ The finished project

A two-player quiz buzzer: a 74HC74 flip-flop for each player, wired so the first press locks the other player out ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 74HC74 10 kΩ 10 kΩ 10 kΩ 220 Ω 220 Ω +− +− AAAAAA3 × AA = 4.5 V+−
A two-player quiz buzzer: a 74HC74 flip-flop for each player, wired so the first press locks the other player out ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 74HC74 10 kΩ 10 kΩ 10 kΩ 220 Ω 220 Ω +− +− AAAAAA3 × AA = 4.5 V+−
Schematic: A two-player quiz buzzer: a 74HC74 flip-flop for each player, wired so the first press locks the other player out 1D21CLK31PRE41CLR12D122CLK112PRE102CLR131Q51Q̄62Q92Q̄8VCC14GND774HC74U1 +4.5V +4.5V +4.5V +4.5V +4.5V reset reset reset reset 4.5 V player 1 10 kΩ RESET 10 kΩ player 2 10 kΩ 220 Ω red LED 220 Ω blue LED
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

On game shows, contestants race to hit a buzzer, and only the fastest one gets to answer. Even if two people press a split second apart, the circuit knows who was first. In this project you’ll build one with the same 74HC74 flip-flop chip from Flip-Flop Memory.

The idea

The chip has two flip-flops: one for each player. Each player’s button is the clock of their flip-flop. Remember, the moment a clock goes from OFF to ON, the flip-flop saves whatever is on its D input.

Here’s the trick that makes it fair. Each flip-flop’s D input is wired to the other flip-flop’s Q̄ (say “Q-bar”), the output that’s always the opposite of what it remembers:

  1. Nobody has buzzed. Both flip-flops remember 0, so both Q̄ outputs are 1. Both D inputs see a 1.
  2. Player 1 presses first. Their flip-flop saves the 1 and their light comes on. Their Q̄ drops to 0, and that 0 is what player 2’s D input now sees.
  3. Player 2 presses too late. Their flip-flop saves… a 0. Their light stays off: they’re locked out.
  4. RESET pulls both CLR (“clear”) pins low, which forces both flip-flops back to 0. Ready for the next question! A 10 kΩ pull-up keeps CLR high the rest of the time.

The two lockout wires cross over each other on the board, just like the cross-over capacitors in the Ping-Pong Flasher: each half of the circuit keeps an eye on the other.

Build it

  1. The chip: 74HC74 across the gap, notch on the left, pin 1 in f14. Red a14 → T+13 (top red + rail, column 13); black j20 → B-20 (bottom blue − rail, column 20).

  2. Rail bridges: red T+4 → B+4 (bottom red + rail, column 4), black T-1 → B-1 (bottom blue − rail, column 1).

  3. PRE pins held high: red j17 → B+17 (bottom red + rail, column 17) and a18 → T+19 (top red + rail, column 19).

  4. Player 1 (left): button in e3, f3, e5, f5. Red a3 → T+3 (top red + rail, column 3). 10 kΩ pull-down j5 → B-5 (bottom blue − rail, column 5). Yellow h5 → h16 (1CLK).

  5. RESET: button in e8, f8, e10, f10. Black a8 → T-8 (top blue − rail, column 8). 10 kΩ pull-up a10 → T+11 (top red + rail, column 11). White i10 → i14 (1CLR) and c10 → c15 (2CLR).

  6. The lockout: orange g15 (1D) → d20 (2Q̄), green d16 (2D) → g19 (1Q̄).

  7. Player 2 (right): button in e26, f26, e28, f28. Red a28 → T+28 (top red + rail, column 28). 10 kΩ pull-down j26 → B-26 (bottom blue − rail, column 26). Yellow b26 → b17 (2CLK).

  8. Lights: player 1’s 220 Ω i18 (1Q) → i23, LED long leg h23, short leg h24, black j24 → B-25 (bottom blue − rail, column 25). Player 2’s 220 Ω c19 (2Q) → c23, LED long leg d23, short leg d24, black a24 → T-23 (top blue − rail, column 23).

  9. Power: 3×AA red into T+1, black into T-2. Press RESET, ask a question, and… buzz! 🛎️

The chip wakes up in a random state, so press RESET first. The build check played a whole quiz on the simulated chip: reset, player 1 first, player 2 too late, reset, player 2 first, player 1 too late. It checked every step from both possible wake-up states.

Not working?

  • Both lights come on? The lockout wires are probably swapped: 1D must go to 2Q̄ (pin 8) and 2D to 1Q̄ (pin 6).
  • A light comes on by itself? Press RESET. If it still happens, check the player’s pull-down resistor.
  • RESET does nothing? Check the white wires reach pins 1 and 13, and the pull-up.

Try it!