Teach Your Kid Electronics

Beginner · Project 5

Dimmer Knob

Add a knob that turns your LED from bright to barely glowing, just like a dimmer switch.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Beginner⏱ About 15 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 3×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 1×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
  • 1×10 kΩ potentiometer (knob)A resistor you can change by turning a knob. Three legs: two ends and a middle "wiper".
  • 1×5 mm LED (any color) — any color worksA tiny light that only lets current flow one way. The long leg is +.
  • 3×Jumper wireA short wire with stiff ends that push into the breadboard.

✨ The finished project

An LED dimmer: battery, 220 ohm resistor, 10k potentiometer knob and LED in one loop ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10kΩ 220 Ω +− AAAAAA3 × AA = 4.5 V+−
An LED dimmer: battery, 220 ohm resistor, 10k potentiometer knob and LED in one loop ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10kΩ 220 Ω +− AAAAAA3 × AA = 4.5 V+−
Schematic: An LED dimmer: battery, 220 ohm resistor, 10k potentiometer knob and LED in one loop R1 220 Ω P1 10 kΩ knob D1 LED + 4.5 V current
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

🔣 New schematic symbols

This project’s schematic has some symbols you haven’t seen before. Here’s what they mean.

  • Knob (variable resistor)

    A zigzag with an arrow through it is a resistor you can change. Turning the knob changes its ohms, so more or less current gets through.

In Light Up an LED you saw that a bigger resistor means less current and a dimmer LED. What if you could change the resistor’s value just by turning a knob? That’s exactly what a potentiometer does. (Say it like po-ten-shee-OM-eh-ter, or just call it a “pot” like engineers do.)

Meet the potentiometer

A potentiometer has three legs:

  • The two outside legs are the ends of a long strip of resistance material: 10 kΩ from one end to the other.
  • The middle leg is the wiper, a little metal finger that slides along the strip when you turn the knob.

If you use one end leg and the middle leg, the resistance between them changes as you turn: from almost 0 Ω at one end all the way to 10 kΩ at the other. That makes it a variable resistor. The third leg just sits in the board, not connected to anything.

Build it

  1. Red wire: T+3 (top red + rail, column 3) to a3.

  2. Resistor (220 Ω): b3 to b7.

  3. Potentiometer: push its three legs into e7, e8 and e9, with the middle leg in column 8. The resistor’s end and the knob’s first leg share column 7.

  4. Blue wire: from the knob’s middle leg column, a8, to a12.

  5. LED: long leg in e12, short leg in e13.

  6. Black wire: a13 to T-13 (top blue − rail, column 13).

  7. Power: battery red wire into T+1, black into T-2. Now turn the knob slowly and watch the LED brighten and dim! 🎛️

What’s happening?

The current goes through the fixed resistor and the knob’s resistance, one after the other (in series, like project 4), so their resistances add up:

  • Knob at 0 Ω: only the 220 Ω resistor is slowing the current. (4.5 − 2) ÷ 220 = 11.4 mA, so the LED is bright.
  • Knob at 10 kΩ: 220 Ω + 10 kΩ = 10.22 kΩ. (4.5 − 2) ÷ 10220 = 0.2 mA, a faint glow.

On the Schematic view, the knob is drawn as a resistor with an arrow through it. The arrow means “this one can change.”

Not working?

  • LED doesn’t change when you turn the knob? You’ve probably used the two outside legs (a fixed 10 kΩ). Make sure the blue wire comes from the middle leg’s column, 8.
  • LED very dim the whole time? Turn the knob all the way the other way. It might have started at the 10 kΩ end.
  • No light at all? Check the LED’s long leg is in e12, and that the knob’s legs are in three different columns.

Try it!