Beginner · Project 4
Two LEDs: Series vs. Parallel
Build the same two lights two different ways, one after the other or side by side, and discover why it matters.
Build this only with an adult present. Before you start, read our safety notice and disclaimer.
🧰 What you need
- 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
- 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
- 3×AA batteryA regular household battery. Each one gives 1.5 volts.
- 1×100 Ω resistor — brown, black, brown, goldA small resistor. Colors: brown, black, brown, gold.
- 2×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
- 4×5 mm LED (any color) — all red works best, so the comparison is fairA tiny light that only lets current flow one way. The long leg is +.
- 8×Jumper wireA short wire with stiff ends that push into the breadboard.
✨ The finished project
🔣 New schematic symbols
This project’s schematic has some symbols you haven’t seen before. Here’s what they mean.
- Junction dot
A big dot where wires meet means they are joined. Current can split up there and take more than one path.
What if you want two lights? There are two ways to hook them up:
- Series: one after the other, like train cars. There’s only one path, and the current goes through both LEDs.
- Parallel: side by side, like lanes on a highway. Each LED gets its own path from + to −.
In this project you’ll build both on the same breadboard, series on the top half and parallel on the bottom half, and see how differently they behave.
Part 1: Series (top half)
Red wire: connect T+3 (top red + rail, column 3) to a3.
First LED: long leg in e3, short leg in e4.
Resistor (100 Ω): from b4 to b9. Check the bands: brown, black, brown.
Second LED: long leg in e9, short leg in e10.
Black wire: connect a10 to T-10 (top blue − rail, column 10).
Power: plug the battery’s red wire into T+1 and black wire into T-2. Both LEDs light up, a bit dim. That’s expected!
Why so dim? The LEDs share the push
Remember that each LED uses up some of the battery’s voltage just to turn on: about 2 V for a red LED. In series, the current has to go through both LEDs, so together they use 2 + 2 = 4 V of the battery’s 4.5 V. That leaves only 0.5 V to push current through the resistor.
That’s why this loop uses a small 100 Ω resistor: (4.5 − 4) ÷ 100 = 5.0 mA. That’s enough to see, but not very bright.
Part 2: Parallel (bottom half)
Unplug the battery’s red wire before you build. We’ll plug it back in at the end.
First, power the bottom rails
The power rails along the bottom of the board are not connected to the top ones. They need their own wires, so bridge them:
Red bridge: connect T+17 (top red + rail, column 17) to B+17 (bottom red + rail, column 17).
Black bridge: connect T-19 (top blue − rail, column 19) to B-19 (bottom blue − rail, column 19).
Now the two paths
Each LED gets its own 220 Ω resistor and its own path from the + rail to the − rail.
Path A, red wire: connect B+3 to j3.
Path A, resistor: from i3 to i7.
Path A, LED: long leg in f7, short leg in f8.
Path A, black wire: connect j8 to B-8.
Path B: the same pattern again, a little further along. Red wire B+10 → j10, resistor i10 → i14, LED long leg f14 and short leg f15, black wire j15 → B-15.
Power: plug the battery’s red wire back into T+1. All four LEDs light up!
Compare them!
Brightness. The bottom (parallel) LEDs are brighter. Each one gets the whole 4.5 V push for itself, so (4.5 − 2) ÷ 220 = 11.4 mA flows through each, compared with 5.0 mA in the series pair.
The pull-out test. Gently pull one LED out of each half:
- Series (top): both LEDs go out. There was only one path, and you just broke it.
- Parallel (bottom): the other LED stays on. Its path is still complete.
Switch to the Schematic view of the diagram at the top of the page. You can see the series pair sharing path 1, while the parallel LEDs each have a path of their own (paths 2 and 3).
Not working?
- Bottom LEDs dark, top ones fine? Check the two bridge wires. The bottom rails get no power without them.
- One series LED backwards? Then neither lights, because the one path is blocked. Check both long legs point toward the battery’s + side.
- Series LEDs very faint or off? Your batteries might be getting tired. Series circuits notice first, since there’s only 0.5 V of spare push. Try fresh batteries.
- One parallel LED dark? Only its own path has a problem. Check that LED’s legs and its two wires.