Teach Your Kid Electronics

Intermediate · Project 6

Color Mixer

Mix red, green and blue light with three knobs, and discover how screens make every color.

Build this only with an adult present. Before you start, read our safety notice and disclaimer.

Intermediate⏱ About 30 min

🧰 What you need

  • 1×Half-size breadboardA board full of little holes with metal clips inside, so you can build circuits without soldering.
  • 1×3×AA battery holder with wire leadsHolds three AA batteries in a row and gives you a red (+) and black (−) wire.
  • 3×AA batteryA regular household battery. Each one gives 1.5 volts.
  • 3×5 mm LED (any color) — one red, one green, one blueA tiny light that only lets current flow one way. The long leg is +.
  • 3×10 kΩ potentiometer (knob)A resistor you can change by turning a knob. Three legs: two ends and a middle "wiper".
  • 3×220 Ω resistor — red, red, brown, goldOur go-to LED resistor. Colors: red, red, brown, gold.
  • 8×Jumper wireA short wire with stiff ends that push into the breadboard.
  • 1×Ping-pong ball — cut in half (ask an adult)Cut in half, it makes a great light diffuser for mixing LED colors.

✨ The finished project

A color mixer: red, green and blue LEDs, each with its own 10k knob and 220 ohm resistor ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10kΩ 10kΩ 10kΩ 220 Ω 220 Ω 220 Ω +− +− +− AAAAAA3 × AA = 4.5 V+−
A color mixer: red, green and blue LEDs, each with its own 10k knob and 220 ohm resistor ++−−++−−aabbccddeeffgghhiijj115510101515202025253030 10kΩ 10kΩ 10kΩ 220 Ω 220 Ω 220 Ω +− +− +− AAAAAA3 × AA = 4.5 V+−
Schematic: A color mixer: red, green and blue LEDs, each with its own 10k knob and 220 ohm resistor + 4.5 V P1 10 kΩ knob R1 220 Ω D1 LED path 1 P3 10 kΩ knob R3 220 Ω D3 LED path 2 P2 10 kΩ knob R2 220 Ω D2 LED path 3 current
The finished build. This picture is generated from the circuit itself and checked by computer, so every leg is in the right hole.

Look very closely at a TV or phone screen with a magnifying glass: you’ll see tiny red, green and blue dots. Every color on screen is made by mixing just those three! In this project you’ll mix them yourself with three knobs.

Mixing light

Mixing light isn’t like mixing paint:

MixYou see
red + greenyellow
green + bluecyan (sky blue)
red + bluemagenta (pink-purple)
red + green + bluewhite!

It’s three Dimmer Knob circuits side by side, one for each color, all sharing the same battery.

Build it

Top half: red and blue

  1. Red knob: legs in e4, e5 and e6. Red wire from a6 to T+5 (top red + rail, column 5).

  2. Red resistor: b5 (the knob’s middle leg) to b11.

  3. Red LED: long leg e11, short leg e12. Black wire a12 → T-13 (top blue − rail, column 13).

  4. Blue LED: short leg e15, long leg e16. Black wire a15 → T-15 (top blue − rail, column 15).

  5. Blue resistor: b16 to b22.

  6. Blue knob: legs in e21, e22 and e23. Red wire from a23 to T+23 (top red + rail, column 23).

Bottom half: green, plus power for the bottom rails

  1. Bridges: red wire T+25 → B+25 (bottom red + rail, column 25), and black wire T-26 → B-26 (bottom blue − rail, column 26).

  2. Green LED: long leg f13, short leg f14. It sits just below the red and blue LEDs. Black wire j14 → B-14 (bottom blue − rail, column 14).

  3. Green resistor: j13 to j8.

  4. Green knob: legs in f7, f8 and f9. Red wire from j7 to B+7 (bottom red + rail, column 7).

  5. Power: battery red into T+1, black into T-2. Bend the three LEDs so their tops lean together, then put half a ping-pong ball over them. It’s a diffuser: it spreads the light out so the three colors blend into one. 🎨

Start mixing!

Turn the red and green knobs up and blue down: yellow! Now try for cyan, magenta, orange, pink… Can you make white?

Not working?

  • One color never lights? Check that LED’s long leg, and that its knob’s middle leg connects to its resistor.
  • Green dead but red and blue fine? Check the two bridge wires that power the bottom rails.
  • Colors don’t blend? The diffuser is the secret. Without the ping-pong ball you’ll see three separate dots.

Try it!